2014年11月3日星期一

LYHY slewing ring bearings Bearing Cleaning

Skateboard bearings cleaning is very simple, get the bearing from the board down with a paper towel to grease the bearings, wipe the stain, wipe the wheels inner wall also high precision bearings will change around the front and rear wheel bearings are smooth and look good. Probably every time, the use of high temperatures generated during rotation of the bearing plate, rubber wheels and bearings will close with a week to clean the walls, causing the wheel to change or replace the bearing so often inconvenient when removing the wheel bearing in accord, reali slim bearings to avoid trouble can simultaneously clean the bearings.
Bearing oil
Remember to clean the oil, a wide range of oil, edible oil all OK, but it was said to buy back the bearing first soaked in gasoline in the week, so it is a waste of gasoline, buy back, after a week cleaning of use when the oil does not matter, bought back the bearing lubricant to prevent bearing rusty oil stored in the oil with the board when you can send bearing, clean the first time when oil cleared on oils, these oils do not play lubrication, simply can mobile crane bearing not be heated like a cylinder of liquid only take effect the same amount, only to prevent rust, but is often difficult with the plate bearing rust.

2014年10月29日星期三

thin section bearing Install accuracy calibration method

After the angular contact ball bearing into the spindle, install precision calibration sequence is as follows (with shaft diameter of 60 100mm ordinary lathe for example):
(A) measuring the shaft and housing bore size, to determine with precision bearings, with the following requirements:
Take the inner ring and the shaft interference fit, crossed roller bearings the amount of interference 0 ~ + 4μm (at light load, when precision is 0); take the outer ring and the bearing bore clearance fit, clearance volume 0 ~ + 6μm (but at the free end of the bearing when using angular contact ball bearings, but also increase the gap); shaft and housing bore surface roundness error in 2μm or less, face parallelism bearing spacer used in the 2μm or less, the end face of the shaft shoulder end foreign beating in 2μm or less; retaining shoulder of the housing bore axis beating 4μm below; cover the front end face of the spindle axis beating 4μm or less.
(2) a fixed end bearings mounted on the shaft before
After the bearings were cleaned thoroughly washed with clean kerosene, grease lubrication, the first containing 3% to 5% of the grease into the bearing organic solvents for degreasing and cleaning, and then quantitative grease gun oil filled bearing (accounting bearing space volume of 10% to 15%); heating bearings make heating 20 ~ 30 ℃, oil presses the bearing into the shaft; pressure in the tight sets with suitable pressure shaft and bearing high precision bearings against the end face axially the spring balance tape volumes on the bearing outer ring, pre-load starting torque measuring method stipulated check whether a substantial change (even if the bearing is correct, but due to meet or maintain the deformed frame, pre-load there; positioning changes possible).
(3) the bearing shaft assembly into the seat hole
Heated seat hole so that heating 20 ~ 30 ℃, with continuous gentle pressure on the bearing shaft assembly into the housing bore;? Before adjusting cover, tighten the amount of the front cover of 0.02 ~ 0.05μm, to the outer end face of the bearing housing benchmark indicator of the conflict in the journal header surface, the axis of rotation measured beat, require error 10μm or less; will dial gauge positioned reali slim bearings on the shaft hole in the surface of the back seat of the header conflict, the rotation axis to measure the bearing housing bore concentricity before.
(4) the free end of the bearing may be selectively placed in the position deviation offset mounted to the bearing support position, to offset possible concentricity and roundness deviation of the deviation between each other.

thin section bearing How to identify bearing

The packaging is clear double row tapered roller bearings under normal circumstances, the regular manufacturers brand has its own dedicated external packaging designers to design, production conditions and arrangements for clearance of the factory production of production, therefore, in terms of product triple row roller slewing bearing packaging lines the color should be very clear and unambiguous.
Seal word is clear
Every product bearing products bearing the body will be in the printed word has its own brand, label and so on. Although the font is very small, but regular manufacturers of products using the stamp printing technology, but without the hot embossing process is carried out, so the font was small, but a deep depression, very clear. And under normal circumstances, not only fuzzy fonts counterfeit products, due to the rough printing technology, fonts floating on the surface, and some can be easily wiped off by hand or hand signs seriously.
Is there a hybrid ring
Left hand holding the bearing sleeve body, right hand toggle coat a small margin to rotate back and forth, listening to the bearings during operation if there is mixed response. Most counterfeit products due to production conditions of backwardness, completely hand-mill operation, bearing the body in the crossed roller bearings production process will inevitably be braced with dust, sand a class of impurities, so that the rotation of the bearing ring or when there will be hybrid phenomenon does not run smoothly . This is to determine whether a product comes from a strict production standards, and the key with the regular operation of the machine manufacturer's brand products.

2014年10月27日星期一

LYHY slewing ring bearings Chamfer is uniform

Are there traces of oil muddy surface which requires that we should pay special attention to when buying imported slewing ring bearings. Very easy to leave a thick oil stains Because there is a certain gap between domestic and foreign advanced technology of rust country of manufacture, so the bearing body cross roller bearings rust treatment, feeling sticky sticky thick hand contact when, while foreign original on imported bearings hardly see any signs of rust oil. According to insiders, particularly observant person can smell the bearings into a special flavor, which is anti-rust oil taste.
The so-called bearing chamfer, which is the junction of horizontal surface and vertical surface, counterfeit products bearing production technology due to restrictions in parts of the processing of these corners was unsatisfactory, which we can easily identify.
Bearing Package
Packaging fair share in the manufacturing of packaging and packaging bearing completed and after passing inspection, namely cleaning and anti-rust treatment, then put the package in order to achieve water, moisture, dust, shock, maintaining quality and precision bearings and the purpose of ease of use and sale.
Bearing inner packing by rust period is divided into triple row roller slewing bearing three categories:
① Short rust on packaging: rust period of 3 to 6 months, for large volume shipments to the same subscriber, then put the bearing used in the short term. By mutual agreement, to facilitate the use of the principle, the use of simple packaging.
② general rust on the packaging: rust period of one year for general purpose bearing.
③ long rust-proof packaging: rust of two years for special and precision bearings.

2014年10月25日星期六

slim ball bearing Angular contact ball bearing

Angular contact ball bearing is a bearing, it can support radial and axial loads. Able to work at higher speeds. The contact angle, the higher the axial load carrying capacity. High-precision and high-speed bearings usually take the contact angle of 15 degrees. In the axial force, the contact angle will increase. Angular contact ball bearings can support radial and axial loads. Able to work at higher speeds. The contact angle, the higher Thin section bearings the axial load carrying capacity. High-precision and high-speed bearings usually take the contact angle of 15 degrees.
In the axial force, the contact angle will increase. Single row angular contact ball bearings can withstand axial load in one direction, while the radial load, will cause additional axial force. And the only limit axial displacement in one direction shaft or housing. If paired installation, so that one pair of bearing outer ring relative to that wide side face of wide and narrow side facing the narrow end. This can avoid additional axial force, and the shaft or housing to limit axial clearance within the range in both directions.
Angular contact ball bearing raceway for its inner and outer rings relative displacement on the horizontal axis, so it can support radial load and axial load - combined load mobile crane bearing (single row angular contact ball bearings can withstand axial load in one direction, So often adopted installed in pairs).
Cage made ​​of brass, synthetic resins, etc., depending on the bearing forms, and application conditions.
Angular contact ball bearings: 7000C-type (α = 15 °), 7000AC type (α = 25 °) and 7000B (α = 40 °) of several types. This kind of bearing outer ring of locking in the general inner and outer rings can not be separated, can withstand radial and axial joint load and axial load in one direction. Axial load capacity from the contact angle, the contact angle is large, the ability to withstand high axial loads. This kind of bearing can limit the axial displacement in one direction shaft or housing.
The main purpose
Single row angular contact ball bearings: machine cross roller bearings tool spindles, high frequency motors, gas turbines, centrifuges, small car front wheel, differential pinion shaft
Double row angular contact ball bearings: pump, blower, air compressor, various types of transmission, fuel injection pumps, printing machinery
Installation Tips
High-speed precision angular contact ball bearings, mainly used for high-speed rotating load lighter occasions, requiring high precision bearings, high speed, low vibration and low temperature rise certain life. Often high-speed spindle bearing installed in pairs, the inner surface grinder spindle speed key component parts.

2014年10月23日星期四

thin section bearing bearing

High-speed precision angular contact ball bearing life of a great relationship with the installation, you should note the following
1 bearing should be installed in the clean, clean room, to carefully matching the bearing, the bearing spacer to be after grinding, while maintaining the inner and outer contour of the spacer premise spacer should be controlled in parallel 1um the following;
2 bearings should be cleaned before installing clean, cleaning the inner slope upward, feel should be flexible, no sense of stagnation, dry, placed in a specified amount of grease, oil mist lubrication should be placed in the case of a small amount of oil mist;
3 bearing installation tool should be used exclusively, even by force, is prohibited beat;
4 bearing store should be clean air, non-corrosive gases, relative humidity less than 65%, long-term storage should be regularly rust.
Maintenance 1, when the bearing to miniature linear bearings run to a certain period of time (or Paul raised maintenance period), will be bearing all removed;
2, with a clean diesel or kerosene soaked with cleaning bearings, if technical conditions for the best open closures cleaning;
3, air dry after cleaning cleaning oil, visual inspection for damage;
4, with about a 150mm, angular contact ball bearing diameter equal to the inner diameter of the stick (preferably hollow tube), one end fixed to a bearing;
5, rapid rotation of the bearing by hand while the stick (wooden pipe) and the other end on top of the microphone audio amplifier or listening to the debate on the ear bearing crossed roller bearings rotation noise;
6, horizontal toggle the fixed bearing sticks, check bearing wear loose;
7, loose serious, turn the noise is too large, there is a serious defect FAG bearings should be eliminated, replaced with the same model;
8, take a bucket of the appropriate amount of grease (high quality yellow dry oil) with gentle heat to melt (not hot), will detect over-bearing into the bucket to soak no bubbles overflow. Bearing grease to cool before removing residual grease less. After cooling remove grease angular contact ball bearings, grease residue quantity. Determine how many of the remaining amount of grease required.
9, with a soft cloth or tissue paper Thin section bearings to wipe the outside of the bearing grease will FAG bearings fitted to the pulley undisturbed security, maintenance work is completed.

2014年10月21日星期二

LYHY slewing ring bearings Angular contact ball bearings

Angular contact ball bearings: 7000C-type (α = 15 °), 7000AC type (α = 25 °) and 7000B (α = 40 °) of several types. This kind of bearing lock port on the outer ring, the inner and outer rings can not be separated in general, can withstand radial and axial joint load and axial load in one direction. Axial load capacity mobile crane bearing from the contact angle, the contact angle is larger, the ability to withstand high axial loads. This kind of bearing can limit the axial displacement in one direction shaft or housing.
Higher speed limit contact ball bearings can support radial load and axial load can also be subject to pure axial load, axial load capacity by the contact angle and the contact angle increases with the increase.
Single row angular contact ball bearings
Single row angular contact ball bearings can withstand axial load in one direction, when the radial load, will cause additional axial force must be applied to the corresponding reverse load, miniature linear bearings therefore, the kinds of bearings are generally used in pairs. Double row angular contact ball bearings can withstand greater radial load mainly radial and axial joint load and moment loads, it can limit the bi-axial displacement of shaft or housing.