2014年10月19日星期日

slim ball bearing Angular contact ball bearings installed in pairs

Paired angular contact ball bearings can bear radial load mainly radial and axial joint load can also be subject to pure radial loads. Tandem configuration can only bear axial load in one direction, the other two configurations can withstand axial load in either direction. After installing preload interference, rings and balls in the axial pre-load condition, thereby enhancing the entire group as a single bearing support stiffness and rotational accuracy.
Back to back configuration, the post code Full complement cylindrical roller bearing for the DB (eg 70000 / DB), back to back pairing separate line bearing load to the bearing axis. Can withstand the effect of axial load in both directions, but the load in each direction only by one bearing. Back to back mounted bearings provide a relatively high rigidity of the bearing arrangement, and can withstand the overturning moment.
Face configuration, the post code for the DF (eg 70000 / DF), paired face-load line bearing the confluence of the bearing axis. Can withstand the effect of axial load in both directions, but the load in each direction only by one bearing. This configuration is better paired back to back with high rigidity, and is not suitable to withstand the overturning moments. This configuration of the rigid and affordability overturning moment is better than DB configurations, bearings can withstand axial load;
Series configuration, post code for DT (eg 70000 / DT), when arranged in series, parallel to the load line, radial and axial loads evenly shared by the bearing. However, acting on the bearing set can only bear axial load in one direction. If the axial load acting on the opposite direction, or if there is a composite load, mobile crane bearing it is necessary to increase a relatively tandem pair bearing adjustment third bearings. This configuration can also be a series of three or more bearings at the same support, but can only carry axial load in one direction. Generally, in order to balance, and to limit axial displacement of the shaft, to be installed at the other support in the other direction to withstand the axial load bearing.

2014年10月17日星期五

thin section bearing Structural deformation types

Double row angular contact ball bearings can withstand the same time characterized by joint load radial and axial load, limiting the axial displacement of both axes. Compared with the two-way thrust ball bearings, these bearings speed limit is higher, the contact angle of 32 degrees, rigid, can withstand the high precision bearings overturning moment, widely used in cars in the front wheel hub (some models also use the same size double row tapered roller bearings).
Structural deformation double row angular contact ball bearings, there are four:
Type A: 90mm outside diameter less than or equal to the standard design of the bearing. No ball gap, and therefore can withstand equal bi-axial load. Using lightweight glass fiber reinforced nylon 66 cage, bearing temperature rise is small.
Type A: 90mm outside diameter greater than the standard design of the bearing. Side of the ball gap, with z steel stamping cage or solid brass cage.
Type E: is to strengthen the structure, the side with filling slots that can hold more of the ball, so a higher carrying capacity.
Both sides with a dust cover type and sides Full complement cylindrical roller bearing with a ring-type, A-type and E-type design design double row angular contact ball bearings with dust cover can be both sides of the (non-contact) or seals (contact). Sealed bearings are filled with a rust-proof lithium grease, generally between -30 degrees to 110 degrees operating temperature. Without re-lubrication during use, before installation is no longer heated.

2014年10月15日星期三

LYHY slewing ring bearings Axial spherical roller bearings

Axial spherical roller bearings and spherical roller bearings Similarly, race raceway is consistent with the bearing center axis as the center point of the sphere, such as spherical roller bearing type, therefore, has a self-aligning feature of deflection and shaft concentricity less sensitive.
And sample other thrust bearing different single direction thrust ball bearing type of bearing axial load capacity is very large, the axial load while also subject to certain radial load, but the radial load should not exceed 55% of the axial load.
As long as the load P and P0 does not exceed 0.05C0, and turn rotary axis, the bearings allow listed in the following table aligning angle.
Aligning bearing angular diameter series aligning bearing angular diameter series 200 Series 1 ° ~ 1.5 ° 300 Series 1.5 ° ~ 2 ° 400 Series 2 ° ~ 3 ° smaller value for larger bearings, and allows increased when the load aligning angle will decrease.
Generally use oil lubrication during use.
Thrust tapered roller bearings can withstand axial load, Thin section bearings can limit the axial displacement of the bearing, it can be used as a one-way axial positioning. And thrust cylindrical roller bearings compared to the carrying capacity of a large, relatively small slide, but a lower speed limit.

2014年10月13日星期一

slim ball bearing Bearing performance characteristics described

1, spherical roller bearing outer ring and housing bore bearings should not adopt an interference fit with the inner ring and the journal should not be too tight, requiring cross roller bearings the use of the adjustment nut in the installation should be able to produce more flexible axial displacement. Spherical roller bearings because if the interference fit, easy to make changes in the contact angle of the bearing, resulting in uneven distribution of load bearing, causing a high temperature. Therefore, the installation with the kind of bearing outer ring and the journal and the bearing housing bore, the general should be able to thumb his hands just pushed into the journal and the bearing housing bore for the best.
2, for spherical roller bearings mounted axial agricultural bearings clearance, the journal is available on the adjusting nut, washer and housing adjustment screw hole, or spring preload adjustment methods. The size of the axial clearance, and bearing installation layout, material from the bearing shaft and bearing between relevant, can be determined according to the working conditions. For high-load high speed spherical roller bearings, adjusting clearance, must consider the impact of temperature on the axial clearance, clearance will reduce the amount of the estimated temperature rise caused by account, that is, the axial travel to properly adjust the gap a little too big. For low speeds and withstand vibration bearings, no clearance should be taken to install, or preloaded installation. Its purpose is to make Spherical roller bearings and roller produce good contact load is evenly distributed, to prevent the rollers and raceways damaged by shock and vibration. high precision bearings After adjustment, the size of the axial clearance with dial gauge test. The method is to first dial gauge fixed in the body or the bearing housing, so that the dial gauge against smooth contact surface of the shaft, the shaft axially pushed around, the maximum amount of the hands of the swing is the axial clearance values.

2014年10月11日星期六

thin section bearing Tapered roller bearings

Tapered roller bearings mainly bear radial diameter, axial joint load. Load bearing capacity depends on the outer ring raceway angle, angle the greater carrying capacity. These bearings are separable bearings, according to the number of columns bearing rolling elements into single row, double row and mobile crane bearing four row tapered roller bearings. Single row tapered roller bearing clearance to be user adjusted during installation; double row and four row tapered roller bearing clearance in the factory based on the given user requirements, users do not need to adjust.
Tapered roller bearings have tapered inner and outer ring raceways, tapered rollers are arranged between the two. All conical surface projection lines are a little get together with the bearing axis. This design makes tapered roller bearings particularly suitable for the accommodation of combined (radial and axial) loads. Most of axial load bearing capacity is determined by the contact angle α; greater the α angle, the higher the axial load capacity. crossed roller bearings Angle size to calculate the coefficient e; e value, the greater the contact angle, the bearing axial load greater applicability.
Tapered roller bearings are usually separated type, that is with roller and cage assembly of components of the inner cone and cone outer (outer) installed separately.

2014年10月9日星期四

LYHY slewing ring bearings Lubrication method

Bearing Maintenance: bearing cleaned up: Assembly nsk tapered roller bearings under the overhaul, the first recorded appearance of bearings, confirm the residual amount of lubricant, lubricant used after sampling review, wash bearings. The tapered roller bearings nsk full immersion is the slot machine lubricating bearings by shrouded brought up, and then back into the oil sump Gulu body should be slightly lower than the lowest place. cross roller bearings Application of such a measure normally smooth grease -20 ~ 120 ℃, while on the positive is 150 ℃ low temperature applications arise from basic oil boiling too fast, run off and serious scenes, greatly extending the life bearing application number. As the clean up agent, generally use gasoline, kerosene. However, because the application of the mineral base oil, so that the kind of smooth and grease are being played on some biochemical indices close buckle rust and rust function outside. Non-break-type medium-sized ball bearings, the inner ring with one hand support level, wind around the outer ring to confirm whether smoothly. Because that kind smooth butter chosen delicate fiber, light melancholy filter to waste lithium thickener, application of mineral oil as the base oil, it is difficult to know the light outside the high-end bearing foot elevated vibration request. In order to Full complement cylindrical roller bearings determine the assembly up nsk tapered roller bearings whether you can use to clean the bearing after being reviewed. Oil can be taken away due to repeated heat determine the bearing cool down, so this law applies to high speed bearing components. Law is suitable for high-speed, high-temperature lubrication of the bearing element. Piles of metal machine grid Xiaobian to introduce 1 bearings are bearing oil bath lubrication are the cause, the use of the amount of fat in the biggest kind of smooth high-speed wire rod roller bearings, accounting division with 70% fat content. With a high pressure oil pump through the nozzle onto the tapered roller bearings nsk, launched into the bearing oil flow into the tank through the other end of the bearing. 2 bath lubricated bearings drip lubricant bearing lubrication in general form, suitable for low speed bearing lubrication. Review raceway, Gulu surface, the surface morphology of cooperation, cage wear, the bearing clearance is added and there is a sense of proportion about the decline of precision damage, strange. Repeat 3 bearing lubrication Taper roller bearings oil lubrication suitable for drip lubricant supply capacity was needed nsk tapered roller bearing elements, drip drop amount is generally advisable every 3-8 seconds, too much oil will cause the bearing to measure improved. Another benefit is a degree of non-inferior good pumping, either greasing machine still works fine greased are concise hard line. A bearing lubrication oil pump spray the filtered oil to the bearing element, after the nsk tapered roller bearing lubricant and then filtered using ice. 5 bearing spray lubrication expansion monotonous atmosphere confused by the formation of the lubricating oil mist sprayer, spray bearings, bearing cyclone may be invalid cool and prevent intrusion of impurities. Moreover, the smooth expensive grease can greatly increase profits nsk tapered roller bearings. When no difficulty on starting and running a positive momentum moment is -20 ℃ testing. When are bearing high-speed wind around Gulu body and cage also make progress commensurate with the high-shrouded atmosphere around the formation of cyclones, with the general form it is difficult to lubricate spherical roller bearing the bearing lubricant sent, then you must use high-pressure jet spray lubricant in the form of to the bearing, the position of the nozzle should be placed is maintained between the inner ring and the place holder.

2014年10月7日星期二

slim ball bearing Spherical roller bearings

Spherical roller bearings with two rollers, mainly bear radial load, but also can withstand axial load in either direction. A high radial load capacity, especially suitable for heavy work loads or vibration, but can not afford pure axial load. This kind of bearing outer ring raceway is spherical shape, so its mobile crane bearing good self-aligning, can compensate concentricity error.
There are two symmetrical spherical roller, there is a common spherical outer ring raceway, and the bearing inner ring with two axis tilt angle of the raceway, aligning with good performance, when the axial force bent or install a different heart while still bearing the normal use, transfer concentric with the bearing size range varies, generally allowable aligning angle is 1 to 2.5 degrees, the larger the load bearing capacity of this type, in addition to radial loads outer bearing can withstand double-acting axial load, has good impact resistance, in general, spherical roller bearings allowed operating speed is low.
Spherical roller bearings under the roller-sectional shape into symmetrical spherical roller and spherical roller asymmetric shape of two different structures, high precision bearings asymmetric spherical roller bearings are early products, the key is for the host service, new design when the host is rarely chosen symmetrical spherical roller bearings, internal structure has been completely improved design and parameter optimization, and early-aligning roller bearings produced compared to withstand greater axial loads, these bearings run lower temperature, it can be adapted to the requirements of high speed, according to the inner wall and used with or without a cage characteristics can be divided into two kinds of type C and CA, C-type bearing is no inner wall and the use of steel stamping cage, CA type bearing characteristics compared to both sides of the inner wall and the use of the car solid cage in order to improve the bearing lubrication, can provide users with an outer annular groove and three hole aligning roller bearings, with bearing post code / W33 said, can also be supplied with inner hole aligning roller bearings based on user requirements, in order to facilitate customer handling and replacement of bearings, but also provide the hole aligning tapered roller bearings, tapered bore, taper 1:12 later code-named K said that in order to meet specific user requirements are also available within 1:30 taper bearings, then set code for K30 tapered ferris wheel bearing bore bearing locknuts are available directly mounted on the bearing cone journal, it can draw an adapter sleeve or withdrawal sleeve mounted on a cylindrical bearing journal. To ensure that the bearing at high speed centrifugal action to prevent harmful slip between the raceway and roller,